Page 1¶
Program Description¶
Product¶
| Name | ND-no. | Category |
|---|---|---|
| UNIQUE UNIQUICK ISAM for ND-500 | 210897A | ROY |
Reason¶
- x New product
Documentation¶
| Title | ND-no. |
|---|---|
| UNIQUE UNIQUICK User Manual | ND-60.240.1 EN |
| UNIQUE UNIQUICK Brukerhåndbok | ND-60.240.1 NO |
Purpose¶
Application generation for UNIQUE-II ISAM
Prerequisites¶
| Computer | Type | Floating format | Op. system | Version |
|---|---|---|---|---|
| ND-500 | SIN III | VSX >=J |
| ND-no. | Product name |
|---|---|
| 210073H | ISAM II, version >=H00 |
| 210895A | UNIQUE-II ISAM for ND-500 version >=A00 |
| ND-no. | Prog.no. | File Name | Type | Containing |
|---|---|---|---|---|
| 210455E | 205489E | DDBTABLES-EQ2 | VTM | Terminal descr. |
Minimum permanent mass storage resources
| User | Userspace | Number of files |
|---|---|---|
| DIALOG-SYS | 230 pages | 7 files |
| File no. | File Name | Type | Containing |
|---|---|---|---|
| 208835A | UNIQUICK-I-A |
MCRO | Load jobs |
| 208836A | UNIQUICK-I-A |
NRF | UNIQUE UNIQUICK ISAM |
| 203449F | PLANC-LIB-F00 | NRF | PLANC library |
Note: UNIQUE UNIQUICK ISAM for ND-500 version A
<rev> must be replaced by the current revision of the DIRECTORY or FILE. The revision level is found on the preceding "ND SOFTWARE LIBRARY DISKETTE" pages.
Known but Not Corrected Errors¶
- If two registers are chosen which both have the same key, UNIQUICK will produce an application which cannot be run by UNIQUE-II.
Page 2¶
Installation Procedure¶
The desired user, for example DIALOG-SYS, should be given 230 pages. Copy all files to this user-area.
The file PLANC-LIB-F00 should be copied to user DIALOG-SYS if it does not already exist. Then you must give 20 more pages to this user. The library must be loaded before loading UNIQQUICK.
An example of how to load PLANC-LIB is shown below:
@ND-500_LINKAGE_LOADER
ND-Linkage-Loader - F 10.september 1983 Time: 00:07
NII entered: 15.April 1983 Time: 16:44
NII: SET-DOMAIN 'PLANC-LIB-F00'
NII: SET-SEGMENT-NUMBER 290
NII: OPEN-SEGMENT 'PLANC-LIB-F00', P
NII: TOTAL-SEGMENT-LOAD PLANC-LIB-F00
NII: END-DOMAIN
NII: EXIT
Run the PERFORM system to load UNIQQUICK. An example is shown below:
@PERFORM_UNIQQUICK-I-A
PERFORM Version G
Macro name [Default = UNIQQUICK-I-500]
*** Load UNIQUE UNIQQUICK ISAM on ND-500 ***
Username for UNIQQUICK:NRF files (Default = DIALOG-SYS)
Username for FORTRAN library (Default = DIALOG-SYS)
Username for PLANC library (Default = DIALOG-SYS)
Type version of UNIQUE-II (1 for A, 2 for B, etc.) [Default = 2]
@MODE MACRO1:MODE,,,
When the mode file has finished, UNIQUE UNIQQUICK ISAM for ND-500 is ready to be run.
Start the program by typing:
@ND-UNIQQUICK-I
Page 3¶
ND Software Library Diskette¶
Page 1
Containing: UNIQUE UNIQUICK ISAM for ND-500
Directory Name: 210897A00-XX-01D
User Name: FLOPPY-USER
| Nr | File name | Type | T | File access: | Pages | Bytes |
|---|---|---|---|---|---|---|
| Public | Friend | Own | ||||
| 0 | UNIQUICK-I-A00 | NRF | I | R | RWACD | RWACD |
| 1 | UNIQUICK-I-A00 | MCRO | I | R | RWACD | RWACD |
| 2 | PLANC-LIB-F00 | NRF | I | R | RWACD | RWACD |
3 files using 130 pages. 610 pages reserved out of 610 pages.